Instructions on how to perform a tilt column steering wheel installation.

When installing our 9050/9051 series Steering Wheel on your 1974-77 Bronco (or anytime you are using a horn relay), you will need to ground the horn button. Here's an illustrated how-to.

Warning: If the rear-most crossbrace in your hood has been cut to install a hood scoop or other modification, we DO NOT recommend installing these hood props. Also, please check to ensure...

This video show the proper installation of our H4 and LED headlights with heavy duty wiring harness.

A common question we receive at TOMS OFFROAD is, “What are my options for modern engine setups?” followed by, “What parts do I need when doing these swaps?” Here we give you multiple scen...

Watch and learn as Matt installs the early Ford Bronco Roof Rack system by TOMS OFFROAD x Rhino-Rack on Jason’s Bronco.

Floor board measurements taken from an Early Ford Bronco with factory sheet metal.

Curious as to where your factory bucket seat holes need to be drilled? This diagram shows measurements taken from an Early Ford Bronco with factory sheet metal.

One of the most common questions we are asked is how to tell if your Bronco has a Dana 30 or a Dana 44 Front End. Once you know what to look for, it is very simple to decipher between th...

An introduction to installing an Early Ford Bronco adjustable tracking bar.

Our early Bronco headers aren't compatible with GT40P heads, but will work with GT40 heads...but what if you don’t know which type of heads you have? This article sheds some light on the ...

We answer your most burning questions about the TOMS OFFROAD x VIVA Chassis Signature Series, from how customizable it is to how the VIN tag process works and more.

Turn Signal Wiring Instructions for factory and tilt column turn signal switches, going to a Factory, Centech, or Painless harness.

Step by step instructions (with photos) on how to install a Dana 20 transfer cases on your early Bronco.

The following is an instruction guide to install our Class III Receiver Hitch for 66-77 Ford Broncos. This hitch can be installed with either factory rear fuel tanks or 23 gallon fuel tan...

Installing a gas pedal spring is easier done with the pedal assembly uninstalled from the firewall, but isn't impossible. Watch this video to see how it's done.

Instructional video and schematic illustrating installation of a wiper cover kit with soft tops.

Get the most out of your heating system with this step-by-step instruction guide on how to install the upgraded heater motor and squirrel cage.

If your dual wiper motor kit is pushing the wiper arms in the wrong direction, this video will help you through the process of "re-clocking" the mechanisms.

Installation instructions for our 68-77 Ford Bronco Deluxe Vinyl Door Panels.

Instructions on how to install TOMS OFFROAD floor board insulation kit, including schematics for placement of insulation panels and sound dampeners.

Schematic showing the 66-73 Ford Bronco Horn Button Assembly on the Factory Original Steering Wheel, complete with TOMS OFFROAD part numbers for easy reference and replacement part reorde...

Diagram showing radius arm drop down bracket installation, including both driver and passenger side installed views.

Check out our step-by-step guide for installing our 1027 series Fold & Tumble rear bench seats.

A short instructional video on how to install seat brackets on our Deluxe Vinyl Denim Front Bucket seats for 1966-1977 Early Ford Broncos.

This schematic is extremely useful in installing new floor pans in your classic Bronco and you have forgotten to take measurements prior to cutting the floor.

How do you remove the stock ignition switch from an early Bronco? If you are having issues installing the ignition switch or tumbler into your 1966-1977 early Ford Bronco, you have come t...

Instructions on how to reset the brake warning light by bleeding the rear and front brake systems.

Step-by-step instructions for installing a high-torque mini starter.

Step-by-step instructions for installing rear dual shock mounts to your 66-77 Early Bronco.

Step-by-step instructions for installing the evaporator and condenser to complete your Early Bronco air conditioning system.

Step-by-step instructions for installing a suspension lift kit to the front and rear of your Early Bronco.

Step-by-step instructions on installing a custom steering wheel in your 66-77 Bronco.

Step-by-step (with photographs) instructions on installing the "No Modify" Power Brake Kit for Early Bronco.

Step-by-step instructions for installing a tracking bar drop bracket on your Early Bronco.

Step-by-step instructions on how to install 66-77 Bronco Extreme Hoop Shock Mounts.

Step-by-step instructions for installing C-Bushing Kit on your 66-77 Bronco.

How to install TOMS OFFROAD's Rear Disc Conversion Kit on a 66-77 Ford Bronco with Factory Ford 9" Rear End

Schematic showing mount positioning for Bronco V8 motor tower.

Guidance on whether you need to install 6-Degree rear leaf spring shims, and instructions for how to do it.Torque Specs 3/8″ Center Bolt — 30lbs. 7/16″ Center Bolt — 40lbs. 1/2″ U-Bolts...

Step-by-step instructions for installing a 23-gallon Rear Main Fuel Tank.

Step-by-step instructions for installing extended radius arm mounting brackets.

Images helpful when working with 6cylinder clutch kit.

Step-by-step instructions with images on how to install a new transfer case yoke.

Images detailing Manual Shift Lever Bushings.

Step-by-step instructions for installing a V8 Power Steering Conversion Kit in your Early Bronco.

Early Ford Bronco Hydraulic Liftgate Support Package U-Bracket (left) | L-Bracket (right) 2 – Hydraulic Liftgate Supports2 – U Brackets2 – Ball Studs2 – Ball Stud L-Brackets ...

Step-by-step instructions for installing an EFI Clutch Equalizer Bracket in your Early Bronco.

Step-by-step instructions for installing an Electric Fuel Selector Valve in your Early Bronco.

Guidance and images for installing either J-Shift and T-Shift Twin Stick Shifters for Dana 20 Transfer Case.